Using microfluidics to isolate circulating leukemia cells

Data from one patient’s liquid biopsy results, for example, showed that the number of CD19-expressing cells dropped over the course of treatment, indicating the patient had moved into MRD. “There were still some signs of CD19-expressing cells,” Dr. Soper said. Examination of the CD19 cells that expressed TdT revealed residual leukemia cells indicative of MRD.

“Because we’re not doing bone marrow biopsies—irrespective of prognostic indicators—we can continue monitoring these patients to make sure there are no signs of relapse.”

Dr. Soper tested seven genes with potential to be prognostic and diagnostic for B-ALL: CD19, WNT5A, CCND2, IL2RA, SORT1, FLT3, and DEFA1. “There is diagnostic capacity in the WNT5A and CCND2 genes,” he said, adding that expression of FLT3 was shown to be particularly prognostic and also useful in AML. Patients with overexpression of IL2RA, SORT1, FLT3, and DEFA1 had increased risks of relapse and death (Garza-Veloz I, et al. Dis Markers. 2015;828145).

A longitudinal gene expression study found significant downregulation of CD19 at the RNA level with treatment progression, particularly in one B-ALL patient. “That’s going to have a profound impact on the amount of leukemia cells we isolate during the enrichment phases of the assay,” Dr. Soper said. The patient’s results also revealed downregulation of the prognostic gene FLT3.

“There are a host of cytogenetic abnormalities that can be used for B-ALL as a prognostic indicator,” he said. For example, an ETV6/RUNX1 fusion transcript indicates that a B-ALL patient is less susceptible to relapse. “Instead of using a bone marrow aspirate, we can gather these cells from blood and do FISH analysis on them.”

Dr. Soper said his laboratory’s microfluidic device for FISH analysis minimizes the time and cost. “The workflow has become less daunting,” which is common with microfluidics, he said. “We can secure results in two hours at about one-tenth of the cost for the reagents required for FISH.” His microfluidic device for FISH analysis uses enriched CLCs obtained by liquid biopsy versus cells from bone marrow biopsy.

The microfluidic assay, reprogrammed with anti-CD138 antibodies (syndecan-1), has also been shown to successfully isolate circulating plasma cells for identification of multiple myeloma-like characteristics. “We were able to stage patients” as monoclonal gammopathy of undetermined significance, smoldering multiple myeloma, or active multiple myeloma, Dr. Soper said (Kamande JW, et al. Integr Biol (Camb). 2018;10[2]:82–91).

“CLCs can be used for a variety of leukemic-based diseases to manage those diseases completely and fully. Even from minimal residual disease, where the CLC burden is low, we can still isolate those cells and monitor for recurrence. We can also look at prognostic indicators, molecular markers, directly from those leukemia cells,” he said.

What makes his team’s technology transferable to the clinical laboratory, even if so many others are not? The difficulties are usually related to fabrication, surface chemistry, and sampling statistics. Of the latter, Dr. Soper said, “Typically, you need to sample large input volumes of blood based on sampling statistics to make sure you catch the target cell, and that becomes somewhat problematic for many microfluidic platforms.”

He and his collaborators fabricate all of their microfluidic systems for clinical applications in plastics, he said, because plastics accommodate high-scale production using the injection molding technique. They can make 1,000 chips a day at about $2 a chip with very high reproducibility, he said. “So this is very accommodating for translation into the clinical laboratory.”

Plastics are attractive for another reason: They have a diverse array of surface chemistries that they can take advantage of. “The surface-to-volume ratio in microfluidics may be about 1,000 times larger than it is in your microcentrifuge tubes. With these plastics you can take advantage of the fact that you can expose them to UV ozone radiation, and when you do that, you change the surface chemistry. You actually add carboxylic acid groups to the surface.” These groups create a functional scaffold from which recognition elements can be attached, like antibodies, “or you make the surface very wettable.”

His lab’s microfluidic consists of an array of microchannels about 25 microns wide and 150 microns deep. There’s an input channel that allows the blood to flow into the device and then disperse through the arrays of microchannels. They have a sinusoidal architecture that collects the tumor cells that have antibodies on them and generates a centrifugal force that pushes the cell against the wall. “The antibodies are poised on these walls. That’s exactly what you need to have happen—these cells, the target cells, need to interact with the surfaces where the antibodies are placed,” he said.

“The longer they roll against this surface, the better the chance you have at gathering up those tumor cells no matter what they are or where they’re coming from. That’s the nature of this device.”

The device minimizes the amount of sample preparation on the front end. “This will process whole blood directly without dilution or lysing the RBCs. Very, very important. Every time you impose a processing step on the front end, you run the risk of contamination or loss of the elements you’re interested in.”

After the blood is washed out, there’s no residual blood components left in the chip. “That’s because we engineered the surface to accommodate minimal amounts of nonspecific absorption artifacts,” Dr. Soper explained.

What is interesting, he said, is being able to capture cells that have low expression of the particular antigen. “This is exactly the scenario you’re typically encountering when you’re looking at patient samples. They’re not like cell lines. It’s not a static picture phenotypically and genotypically of that cell. There’s a diverse range of different types of cells with different expressions of the target antigen.” He and his team designed the device in such a way that it can capture cells that have expression levels targeting antigens down to about 700.

“To put this in a frame of reference for you, the CellSearch technology has a limit of detection in terms of the antigens per cell of about 17,000 to 20,000. It’s several orders of magnitude higher.”

The device is also scalable. The channel architecture is thin, 25 microns, but deep to keep the throughput high. “We can process several milliliters of blood in less than an hour by generating the correct number of sinusoidal channels in the device, and the appropriate flow rate.”

A large-scale clinical study using the chips is underway for PARP inhibitors for pancreatic cancer, Dr. Soper said. “But it’s using EpCAM to gather up CTCs for pancreatic cancer.” The challenge with using anti-EpCAM antibodies, he said, is that cells undergo EMT-type (epithelial-to-mesenchymal) transition; they downregulate EpCAM. “So what we’re doing there is adding not only the EpCAM marker to enrich these cells but also a different marker that’s targeting these EMT or mesenchymal-type cells that have undergone EMT. That increases the number of cells we gather up, and we then have to do molecular analysis in that clinical trial, so we’re doing targeted NGS on those CTCs.”

For B-ALL, he and his team are working with collaborators at Children’s Mercy Hospital, where the pilot study of 20 patients was done, to scale up the sample to several thousand patients. “We’re now scaling that up to use circulating leukemia cells as an indicator of relapse in those patients,” Dr. Soper said.

Amy Carpenter Aquino is CAP TODAY senior editor.